Dwarf User Guide

From MOD Wiki
Jump to navigation Jump to search
The MOD Dwarf when powered up

Warnings

RISK OF FIRE, ELECTRICAL SHOCK OR PRODUCT DAMAGE

  • Do not expose the apparatus to rain, moisture, dripping or splashing and avoid placing objects filled with liquid, such as vases, on or near the apparatus.
  • Only use accessories approved by the manufacturer.
  • Do not open the enclosure. There are no user repairable parts inside. Leave service and repairs to trained service personnel only.

AUDIO OUTPUTS WARNING !

  • Always mute or turn down the volumes before connecting any equipment to the audio or headphone outputs.
  • The apparatus is capable of outputting loud signals via the audio and headphone outputs. These volume levels may damage your gear. Verify that the output volume is set to a level that your equipment can handle.
  • High volume levels may damage your hearing, please protect your hearing by paying attention to the output volume.

POWER ADAPTER WARNING !

  • The adapter may only be used indoors
  • To ensure adequate ventilation, do not place the power adapter in tight spaces.
  • To prevent the risk of electric shock and fire because of overheating, please ensure that curtains and other objects do not prevent adapter ventilation.
  • Use supplied adapter only

Overview

The wireframe images below expose the controls and inputs/outputs that the MOD Dwarf has.

Dwarf UsageOverview.png

Device features

Inputs and outputs

Dwarf ConnectionsOverview.png

Audio input jacks

The MOD Dwarf has two independent audio inputs, with configurable input gain for each input. You can set up the input gain through the device menu.

Audio output jacks

The MOD Dwarf has two independent audio outputs, with configurable output gain for each output. You can set up the output gain through the device menu.

Headphone

The headphone output on the MOD Dwarf monitors outputs 1 and 2. It is possible to set the volume level of the headphone output through the device menu.

Power jack

The MOD Dwarf comes with its own power supply which outputs 12V, 2A over a center-positive barrel-type plug.

The plug diameter of the power supply must be Φ5.5*2.1*10mm

In summary, the power consumption of the MOD Dwarf varies depending on the peripherals connected to the device. For example: Hooking up a USB-hub to the USB-A port, and then hooking up multiple MIDI controllers to the hub will change the power requirements.

By using the provided power supply you are sure that you will never run out of juice.

Control Chain port

MOD Control Chain devices (such as the MOD Footswitch) have multiple benefits over MIDI Controllers.

MOD Control Chain devices have screens that show you on-demand what each of the footswitches (or other actuators) is assigned to control.

You can daisy chain up to 8 Control Chain devices (this was the maximum we tested) using a single cable from one Control Chain device to the other.

MOD Control Chain devices use an open protocol, which means that you and all of our community can contribute to improving it. You can also use the Arduino Shield and build your own Control Chain device.

Last but not least, Control Chain devices also allow you to have more resolution from your actuators than the current MIDI Controllers.


NOTE: Please do NOT connect this port to a regular Ethernet port, it can damage your MOD Dwarf.

USB Host port (USB port A)

In the most common scenario, this port is used to hook up a single USB-MIDI device, such as a MIDI-keyboard to control generator plugins.

Another common scenario is using this port to hook up a Bluetooth dongle for wireless connection to your PC.


Applications: USB MIDI Host, USB Bluetooth (with dongle), USB Flashdrive (making device backups)

USB computer port (USB port B)

This port is mostly used to connect the MOD Dwarf to your PC for setting it up.

When executing a manual system update, its use changes to a mass-storage device, so that you can copy the update file to the MOD Dwarf.

Applications: USB Ethernet (for web interface), USB Mass Storage (for updates), USB MIDI

MIDI I/O

The MOD Dwarf also supports "old-school" MIDI devices. For that, the Dwarf uses two TRS 3.5mm ports. These can be directly connected to other devices using TRS MIDI Type-A, using a 3.5mm TRS cable. It is also possible to connect a dongle to convert it to DIN-MIDI. This dongle should be of the "Type A" and will allow you to hook up your "old school" DIN-MIDI devices. Make sure to use the right type of dongle!

Actuators

Dwarf Actuators.png

Endless knobs

On some parameters, you can push the endless knob in order to access a full-screen view of the parameter and/or lists.

On each of the knobs, you can have different parameter types:

  • Knob: turn for precise value change, hold and turn for coarse value change;
  • Trigger: turn left, turn right or click to trigger;
  • Toggle: turn left for off, turn right for on, or click to toggle;
  • List: turn left to open list and select prev item, turn right to open list and select next item, click to open/close overlay, hold then turn then release to open the list then change the value then immediately close the list.

Menu button

To the left of the Dwarf's screen, you can find the Menu button.

You can edit the Menu Items showcased on this menu on the Settings of your MOD Dwarf. (picture with close up of this button)

Display

The MOD Dwarf has a large (2.9") LCD display. The display normally gives dynamic information about the actions mapped to the device actuators, but they are also used for displaying the device menus and tools.

Control Mode

Dwarf Display.png

Each part of the display corresponds to one of the actuators. (See the image above)

The top section of the display shows the Current Pedalboard or Snapshot name. You can define it on the Device Settings.

The section below it shows the control mapped to the endless knobs.

The following section represents the three assignable pages for the endless knobs on the MOD Dwarf.

On the left of the bottom section, you can check the current actuators assignment page, while the two elements on its right show the name of the plugin parameter assigned to the footswitches A and B (correspondingly) according to the current assignment page.

Switching pages

The MOD Dwarf allows you to switch between 8 pages and 3 subpages. This means that each of you the 3 endless knobs on your Dwarf can be assigned up to 24 parameters. The footswitches B and C can be assigned up to 8 parameters each.

(screenshots of assignment pages)

Navigation Mode

(image similar to the top one but with Navigation Mode)

Tool Mode

On the Tool Mode of the MOD Dwarf you have access to multiple tools. You can define the default one on the device settings, check here how to do it.

The default tool will be that one showcasing in the first place when you access your Tool Mode. Independently of your default tool, you can always scroll between all the tools by pushing the Footswitch A.

The MOD Dwarf has currently available the following tools:

Tuner

Dwarf Tuner.JPG

The MOD Dwarf has a built-in chromatic tuner. Both inputs can be used as the tuner input, to select between them push the right footswitch.

If you see a question mark on the tuner screen, it means the MOD Dwarf is not receiving any input or the input levels are too low. (image of the screen with a question mark)

By pushing the footswitch B you activate the mute feature. With the mute feature active when you access the Tuner tool your MOD Dwarf will mute.

Please refer to the Tuner section in the Device Settings page for more information.

Tempo

Dwarf Tool-Tempo.jpg

The MOD Dwarf has a built-in tool called "Tempo". This tool allows you to define the main tempo settings in your MOD Dwarf.

On this tool, you can define the time signature (aka beats per bar), the BPMs (beats per minute), and the Clock Source on your device.

By turning the left-most endless knob you will set the number of beats per bar.

By turning the central endless knob you set the number of beats per minute. You can also use the tap tempo feature, for that you must tap the Footswitch C. Note also that the LED above the Footswitch C blinks according to your current BPM.

Turning the right endless knob will scroll all the available options of Clock Source (Internal, MIDI, or Ableton Link). Note that when your clock source is MIDI the Footswitch C changes its function to be a toggle activating and deactivating the MIDI sync.

On this tool, Footswitch C is assigned to start and stop the tempo tool.

LED Audio meters

The input and output LEDs on the top of your MOD Dwarf have smooth transitions between colors. The LED colors represent the following input levels:

  • Off: below -40dB
  • Green fade in: between -40dB and -6dB
  • Green fully ON, fading in yellow: between -6dB and -1dB
  • Red: between -1dB and 0dB
  • Blinking strong red: 0dB (CLIPPING!)

Dwarf gain staging

(diagram of gain staging on the Dwarf)


WIP--------

Device Settings

Pressing Menu Button followed by the left-most button will open the Device Settings menu.

Access the Device Settings page to learn how to use it to Load Banks and Pedalboards, adjust volumes and MIDI Settings, manage User profiles, and more.

Dwarf Settings.JPG

Editing

Accessing the graphical interface

The MOD Dwarf has a built-in graphical user interface (GUI), which means you don’t need to download any extra software in order to configure the device. To access the interface, you only need a web browser, such as Chrome, Safari, or Firefox.

Once you are connected to your device you will be able to build and share your pedalboards, download new plugins, organize your banks for offline access and much more.

Please refer to the Web GUI User Guide to learn all about it.

Overview shot of the pedalboard builder in the web interface

Accessing via USB cable

The easiest way to access the GUI is through the USB cable. Simply connect the USB cable, which you received along with your MOD Dwarf, to your PC or Mac. The operating system should recognize the MOD Dwarf as a network device and configure it automatically. However, this process may fail in certain Windows versions, if that is your case please check the troubleshooting page

After successfully connecting the MOD Dwarf to your PC or Mac, open your favorite browser and navigate to http://moddwarf.local/ (or http://192.168.51.1).

Accessing via Bluetooth

It is also possible to connect to your computer using a wireless Bluetooth connection. Check this page to see how to do it!

Dwarf Bluetooth.JPG