Difference between revisions of "MOD Duo User Guide"

From MOD Wiki
Jump to navigation Jump to search
Line 23: Line 23:
  
 
From this point onwards, you can use multiple ways of navigating through the pedalboards in the active bank:
 
From this point onwards, you can use multiple ways of navigating through the pedalboards in the active bank:
1. Repeat the procedure to navigate to and select a different pedalboard
+
# Repeat the procedure to navigate to and select a different pedalboard
2. Use the footswitches on the MOD Duo to cycle through the pedalboards inside the currently active bank (only if set up through the web interface)
+
# Use the footswitches on the MOD Duo to cycle through the pedalboards inside the currently active bank (only if set up through the web interface)
3. Use MIDI program changes to select the currently active bank (only if set up through the web interface)
+
# Use MIDI program changes to select the currently active bank (only if set up through the web interface)
  
 
==Current pedalboard==
 
==Current pedalboard==

Revision as of 13:17, 2 November 2016

Overview

Device features

Inputs and outputs

Actuators

Displays

Device menu (HMI)

The device menu, or as we call it, HMI (Human Machine Interface), allows you to change settings on the MOD Duo. It also allows you to access different banks, pedalboards and the tuner.

The device menu can be accessed by holding down the left knob for one second.

Navigation is done by rotating the left knob until the desired section is highlighted. Click on the left knob to enter the highlighted section.

When you are done, you can either navigate to "Back to SETTINGS" and click on the left knob to go back to the device menu. Or you can hold down the left knob for one second to exit without going back to the device menu.

Banks

If you want to use the MOD Duo without being connected to a computer, this is a very important section.

Upon entering this section, you will see the banks that you have created using the web interface, as well as a bank that contains all your pedalboards, named "All".

By navigating to a bank and clicking on the left button, you can browse the pedalboards within that bank. Navigate to the pedalboard of your choice and click the left button to load that pedalboard, and make the bank the currently active bank.

From this point onwards, you can use multiple ways of navigating through the pedalboards in the active bank:

  1. Repeat the procedure to navigate to and select a different pedalboard
  2. Use the footswitches on the MOD Duo to cycle through the pedalboards inside the currently active bank (only if set up through the web interface)
  3. Use MIDI program changes to select the currently active bank (only if set up through the web interface)

Current pedalboard

If you have made some changes to some parameters of your pedalboard, and you want to save those changes for the next time you load the pedalboard, you can enter this menu and select and click on "Save State". This is especially useful for use without a computer.

If you have made some changes, but you are not quite happy with the result, there is also a "Reset State" command. This command will return your pedalboard to the original saved state.

Volume and gains

This section allows you to set the gain for the inputs and level of the outputs. The headphone has its own section, so check out the "Headphone" section for information about the headphone volume levels and settings.

When you notice that the LED's at the input side are blinking bright red, that means that your input signal is "clipping". In general, that is not a desired condition. Luckily, it can easily be resolved by lowering the input gain. Try a different gain-stage for the clipping input, or use the "Fine Adjust" option to take smaller steps.

The gain stages represent the following input gain: Low: -22.0 dBu Medium: -9.5 dBu High: +3.0 dBu

For the outputs there is only a simple volume control, going from 0 (unity gain) all the way down to -127.0 dBu. It is recommended to keep the outputs set to unity gain, and resolving clipping on the outputs by reducing the gain in the pedalboard.

Headphone

Bluetooth

Info

Tuner

By holding down the right knob for one second, you will go into tuner mode.

Changing the input being tuned can be done by clicking on the right knob once. By default the tuner is set to tune input 1.

Exiting the tuner is done by holding down the right knob for one second again.

Hooking up the MOD Duo

Wiring examples

Guitar

Vocals

Keys

MIDI

Exotic